Showing posts with label sail trim. Show all posts
Showing posts with label sail trim. Show all posts

Monday, 5 November 2007

How to Point, Foot, and Shift Gears

How to Point, Foot, and Shift Gears
Shifting gears is on a boat is one of the most difficult aspects of sailboat racing and requires a knowledge of your boat, the conditions, and plenty of practice. Greg Fisher breaks down how to find the baseline, and then shift gears to get your boat going fast in all conditions. From the SW Archives, our June 1998 issue.
Jul 25, 2006
By Greg Fisher (More articles by this author)

http://www.sailingworld.com/from-the-experts/technique/how-to-point-foot-and-shift-gears-200894.html
Subtle gear changing is what truly separates those with just adequate boatspeed from those who always seem to be a click quicker and higher. While most of the fleet starts the race with a similar setup, created with the help of a tuning guide or by following standard principles, the fast boats are constantly making additional adjustments. When conditions suddenly change—a puff hits, or powerboat waves arrive—these sailors shift gears smoothly. Before we dive into the subtleties of their sail adjustments, let’s take a look at how you might create a basic pre-race setup.

Step 1: Set the depth
Try to memorize the depth that feels about right in 10 knots of breeze. Then set your mast bend and headstay sag to replicate that shape, using it as your starting point in other velocities. Another method is to increase mast bend until you just begin to see slight wrinkles (called inversion wrinkles) running from the clew of the mainsail to the lower quarter of the mast. For the jib, decrease headstay sag until you are just able to make the telltales on both sides of the sail fly easily. Any tighter, and the steering groove will become too narrow.

Step 2: Set the draft position
For most boats, the main draft should be positioned nearly halfway back. Pulling the cunningham tighter pulls the draft forward, while easing it allows the draft to move aft. Use the jib halyard or jib cunningham to position the fullness in the jib. The draft should be slightly farther forward than in the main, usually about 35 percent, or roughly one-third, of the way back.

Step 3: Set the twist
To set the leech tension for the main, sight from under the boom and set the sheet so that the chord of the top batten is parallel to the boom. For the jib leech, set the sheet so that the last 6 inches of the middle of the leech (a mid-leech batten helps here) are parallel to the centerline of the boat. Easing the sheets allows the outboard end of the battens to fall away, increasing twist. Trimming the sheets does the opposite, decreasing twist.

Step 4: Set the angle of attack
If you drop the tiller, the boat should continue to track straight, or slowly head up into the wind. Any more helm than that means excessive rudder drag. If the boat has excessive windward helm, ease the traveler to until the helm is balanced. This four-step process for setting your sails is only a starting point. It’s still a great idea to line up with someone you know is fast before the race to see if you are "on the money." If you’re faster, great! If you’re off the pace, just ask your crew, "Are we lacking speed or pointing ability?"

Solving Pointing Problems
An inability to hold a lane or position close to other boats can really destroy a tactical game plan. Pointing problems are not so much indicated by the angle that the boat seems to be sailing relative to the boats around us, but more by the fact that the boat is actually sliding to leeward.

Trying to pinch to maintain height can be the crux of the problem. The old adage, "foot, then point," says a lot. A boat needs to go fast before the underwater foils can develop enough lift to hold their position in the water. To regain pointing ability, ease the sails out, bear off slightly, and get back up to speed. Once up to top speed, re-trim to your starting point trim and reevaluate your pointing problem. If the problem persists, check your sail trim.

When sail trim is the cause of the problem, it’s usually the main, not the jib. The upper leech of the main provides most of your pointing ability. Be sure to trim the main so the upper batten is at least parallel to the boom. If you need more pointing ability, try trimming the main tighter. You can hook the upper batten as much as 15 degrees to weather for short periods. Avoid the temptation to overtrim the jib to help pointing ability. Hooking the jib leech will choke the slot between the main and jib, stalling the entire sailplan. The jib should never have less twist than described in the "basic setup."

Only after you’ve decided to trim the main harder should you try to pinch the boat. In this mode, the weather telltales on the jib will be stalled. In big puffs, the luff of the jib can break as much as 8 inches back. This "super pinch" mode can only be held for short bursts and in flat water. Once the boat starts to slow down, be sure to ease the sails out, regain your speed, then start the process again.

While it may seem natural to let the boat heel more when trying to point, fight the urge. Keeping the boat flat will help maintain a balanced helm and maximize the efficiency of your underwater foils. Still not pointing? Either your rig is too loose, resulting in too much headstay sag (i.e., the jib is too full) and sometimes too much mast bend, which makes the leech too open, or the luff tension on either sail is too tight (the draft is too far forward).

Solving Footing Problems
What if your pointing is fine, but your straight-line speed is lacking? The simplest fix is easing the sails. More open leeches on both sails will help the boat sail lower and faster in a straight line. Sometimes, however, this results in a pointing problem. If so, first check your helm balance. Weather helm can seriousIy hinder the boat’s ability to go fast. Instead of easing sheets, it’s often better to find a way to ease helm. First, try to sail the boat more level. If you can’t keep the boat flat, induce more mast bend to flatten the main. The next step is to ease the traveler until the helm is balanced. Finally, tighten the outhaul, tension the cunningham/jib halyard to pull the draft forward and open the leeches of both sails.

Gear Shifting: Puff On!
We’ve got you going with good speed and good height. Then what happens? The wind velocity changes and it’s time to shift gears. First, let’s look at some of the automatic trimming change that should happen as soon as a puff hits. 1. Ease the main, and sometimes the jib 2. Steer up to "feather" the boat 3. Re-trim sails.

Since a puff typically lifts you, due to a change in the apparent windspeed, you need to ease sheets and head up as it hits. Be sure to let the boat climb up into the wind and steer toward the upper end of your groove with the jib luff actually breaking. In flat water, all that may be required is a quick ease of the mainsheet. But in chop, it may be necessary to ease the jib as well.

If the puff packs some real velocity, more adjustment may be necessary. If you can’t hold the boat down, and there’s still too much helm, try the following, one at a time, until the helm is balanced. 1. Ease the traveler 2. Bend the mast (vang tension, backstay tension, etc.) 3. Tension the cunningham on both main and jib.

Gear Shift: Into a Lull
For the same reason that puffs are lifts, lulls usually appear as headers. In a lull, it’s important that you bear off as smoothly as possible. Make sure the boat remains flat and resist the temptation to add heel to maintain "feel" in the helm.

Ease the main so the top batten angles outboard from parallel to the boom. Leave the jib trimmed initially until the bow is pulled down to the lower end of your groove with both telltales streaming aft. At that point, the jib should be eased so the leeward telltale doesn’t stall.

Here’s how to maintain speed in a lull. 1. Ease the main 2. Allow the boat to heel to weather, creating lee helm, to steer the boat down 3. Ease the jib 4. Level the boat 5. Pull the traveler up (if the boom is below centerline).

If the lull is long-lived, you may need to take additional steps to maintain speed. 1. Straighten the mast and induce luff sag in the jib 2.) Ease main and jib cunninghams to maintain correct draft position. The smoother you shift gears the faster you’ll be, so practice until it’s automatic. Heck, manual transmissions went out years ago!

Saturday, 3 November 2007

Learning the Ropes

Learning the Ropes: "With my partner making large adjustment changes, I could sit forward and watch mast, main and jib changes. When he pulled on the boomvang, the mast bent low, the main flattened, the leech got tighter and the jib luff sagged off. When he pulled on the mast fore puller the mast bent lower, the main flattened, the leech got looser and the jib luff sagged off. When he pulled on the mast aft puller, the opposite happened. When he pulled on the main cunningham the draft moved forward, the leech got looser and the sail got flatter as the mast section above the hounds fell off to leeward. When he pulled the mainsheet in, the mast bent, the mainsail got flatter, the leech got tighter and the jib luff got tighter. The opposite happened when the mainsail was eased. With this knowledge, scenarios developed in my mind. As the wind builds, the mainsheet gets trimmed tighter and both sails flatten simultaneously. Perfect reaction. However, when the mainsheet must be dumped for larger puffs, both the main and jib get fuller. Bad reaction. To combat this we can use the vang, which flattens the main but makes the jib fuller, To improve this we can tighten the aft puller, which flattens the jib but powers up the main. Using both the boomvang and the aft puller, their negatives and positives combine to create the best compromise to flatten the main while controlling jib luff sag. With the mainsheet in tight, the main and jib are flat. When the main must be dumped in a puff, the aft puller and the vang help maintain that sail shape. In real high winds you also pull the main cunningham hard to flatten the top of the sail. These discoveries dramatically improved my heavy air speed.

                            CAUSE AND EFFECT

CONTROL MAST MAIN JIB
---------------------------------------------------------------------------
Vang bends low flatten, leech tight sags
Fore Puller bends low flatten, leech loose sags
Aft Puller straighten low full, leech tight tight
Main Cunningham tip to leeward draft foreward, leech loose --
Mainsheet--in bends flatten, leech tight tight
--ease straightens full, leech loose --

Heavy Air--Combine these for maximum effect

Vang flatten full
Aft Puller power-up flat
Main Cunningham flatten top

Problem solving is part of sailing. Knowing the effect of all your adjustments and confidently making these changes during a race is part of the success formula. In shifty, puffy winds it is better to set these adjustments for the lighter end of the wind range instead of making an adjustment for every wind change. Too much time is spent making sail adjustments and not enough time keeping track of the next wind shift. Setting your adjustments for the lighter end of the wind range is best as it is easier to keep your boat speed up in heavy air when setup wrong than it is in light air. Do your best to set up correctly but be wary of losing track of the race.

Successfully racing your boat should be much like sitting on the couch at home. There you have the TV clicker and the cordless phone within reach and you know how to lie on it to be the most comfortable. Your boat should be the same. All my Snipes I have either rigged myself or specified where the hardware would be placed. Rigging is highly personal and must adapt to the interests of each team of people. Decide who is going to do each job and place the controls near that person. Every adjustment must be positioned to make sense relative to when it is used. The upwind adjustments must all be within reach when hiking with the downwind or light air upwind adjustments put inside the boat to avoid deck clutter, putting too many adjustments in one place requires a distracting glance to confirm that you have the right line. When action is quick in a race, a well thought out deck layout is worth boat lengths on the course.

Good sailing

http://www.snipe.org/articles/ropes.html

Craig Leweck is a sailmaker for Sobstad Sailmakers in San Diego. Craig has been US National Champion twice and has won the North American Championships. He has represented the US in two World Championships, and continues to finish in the top at regattas on the US Circuit.


Return to the Snipe Page"

Wednesday, 3 October 2007

Sailing Upwind through A Chop in Lightning

Sailing Upwind In A Chop

http://www.lightningclass.org/Articles/SailingUpwindInAChop.htm

By Greg Fisher
Columbus, Ohio
Fleet 353, Hoover Yacht Club 1990 North American Champion

(From Racing the Lightning)

Steering a Lightning through a heavy chop is not an easy task. The “resonation” made by the bow slamming the waves when it isn’t “done right” is the best tattletale there is of improper tune and steering. While it isn’t possible to miss them all, there are some things that can be done, sail trim, tuning, and steering wise to help make the job a little bit easier.

The natural inclination when sailing through chop is to power the boat up as much as possible. While obviously the boat does need extra punch, how that punch is directed is most important. The first indication that the boat is not set up just right and that there is maybe too much power for the wind is the feel at the helm. If there is too much weather helm (the boat wants to round up into the wind) the boat will be very difficult to steer through the chop. Excessive weather helm means the tiller will be pulled to windward of centerline and the rudder will be literally dragged through the water.

Usually it is not too little backstay or too much mainsheet that creates the problem of excessive weather helm. Most Lightning sailors are comfortable with setting the mainsheet so the upper batten is angled outboard slightly from parallel to the boom. Most also just pull the backstay until the slop is just barely removed (unless it is blowing really hard). However, it is the traveler position that usually unbalances the boat. Normally we think that we want to pull the traveler up to a point where the boom is close to centerline since the mainsheet is eased and the upper batten is open. However, the bottom of the main is still powerful and the lower leech is hooked in relation to the centerline of the boat. In chop it is not unusual in a 8-10 mph breeze for the traveler to be down to leeward perhaps as much as 6”. Actually, the true gauge will be the feel on the helm. The helm must be nearly balanced so the boat can almost steer itself straight upwind all by itself. In flat spots, the traveler can be pulled back near centerline and the mainsheet trimmed to the batten parallel to the boom position. However, as soon as the boat enters waves again, traveler must go down and the sheet eased.

It is also natural to want to heel the boat a great deal because it seems to put a more ”V’ed” hull shape to enter the waves. While this may be true, a boat sailed with more heel develops more windward helm. Instead, try to keep the boat flatter, maintaining the weather chine no more than 3" to 6" out of the water. Many Lightning sailors sail with the chine just barely touching the water so that the boat is only heeled 10 degrees at the most. A boat that is balanced and sailing fast can still be steered to miss the biggest waves.

Steering around the waves should not be accomplished with only the tiller. The more the tiller is wiggled, the greater drag and the more the boat will slow down. Instead, ease the mainsheet (sometimes as much as a foot) to help the boat bear off and then trim it back in to help the boat head up. Be sure when trimming the main back in not to overdo it so the weather helm again won’t load up.

Be sure to adjust the jib also as the-boat heads up and bears off, but don’t overdo that either. If the jib is eased more than the ease of the main, the boat will not have the tendency to bear off and it will be much more difficult to "steer" through the waves. Unless it is extremely light, the jib should be eased out so the batten is angled close to the tip of the spreader and never trimmed inboard more than 1" to 1.5" inside the tip. In light winds, don’t be afraid to ease it out to as much as 2” outside the tip of the spreader.

Check that the extra life jackets, tools, water bottles, spinnaker poles, etc. are brought in from the ends of the boat and centered as close to the centerboard pin as possible. The crew weight too needs to be centered close with the skipper moving forward and the forward crew moving aft to help minimize the boat’s tendency to hobby horse through the waves.

Finally, be careful to avoid pinching at all costs. A boat that is going fast through the water will go up and over the waves much easier than one that is slow and loaded up with excessive weather helm.

Good luck and happy slamming.

Another sail trim guide

http://www.mssa.org/cms/pdf/pub/MSSAsailTrim.pdf

How to Maximize Lift

(and minimize drag)

• Lift and drag is variable

• Sails may be adjusted:

– Light Air

• Deep Draft, Draft Aft, more sail area

• Fuller shapes work because light air produces less

drag.

– Medium Air

• Reduce Draft, Draft Forward, maintain sail area

• Flatter shapes provide lift without excessive drag

– Heavy Air

• Reduce sail

– High wind velocities produce sufficient lift with much less

sail area.

– Overpowered is not fast

– Smaller flatter genoa/jib

– Reefed mainsail, full out haul to flatten the mainsail

General Sailtrim/Boatspeed

Guidelines

• Light Air, Flat Seas

– Sail trim

• Full Shapes, deep draft

• Ease halyards, Outhaul and Cunningham

– Steering

• Foot off to keep the boat moving. Helm and Trimmers work

together to continually adjust sail and helm to the varying

conditions. As boat speed increases, point a little higher to

make distance toward the mark.

–Move crew to leeward

• Keep the boat heeled so it is ready to take advantage of any

– breeze.

• Light Air, Choppy seas

– Arrgh! This is the worst!

– Foot off, keep boat moving, one wave can stop

you dead in your tracks, and take minutes to get

moving again. Don’t be greedy and try to point

too high.

• Move Crew to Leeward

– – Try to sails from collapsing/flopping

• Medium Air, Flat Seas

– Yeah! This is by far the easiest to sail

– Start reducing draft in the sails (flattening)

• Outhaul

• Halyards (move draft forward)

• Cunningham

– • Genoa Sheets and Car Position

• Medium Air, Choppy Seas

– With a continuous breeze, it is easy to get the

boat moving.

– Watch for the waves, if you hit one head on,

you will loose momentum. If you are about to

take a wave on the bow, steer down,

momentarily.

– – Anticipation is key, don’t get caught sleeping

• Heavy Air, Flat Seas

– This is a transition state, most likely the wind

has just come up.

– You will need to reduce, flatten sail.

– Don’t be fooled. This state is short lived. The

waves will likely come soon. Use this time to

– get ready.

• Heavy Air, Choppy Seas

– Reefed main, Tight Halyards, Cunningham

– Small, Flat Genoa

• 90% to 110% Genoa is in order

• Roller Reefing will reduce sail area, but don’t

expect to point very high.

– Watch out for big waves, they’ll stop you dead

– in you tracks.

• Velocity Made Good (VMG)

– Strong Winds

• Sail more direct course toward mark, Run down

wind, boat speed will be maintained for Best VMG

– Light Winds

• Sail more of a broad reach to maintain boat speed

– for best VMG.

Down Wind Sail Trim

• Loosen most sail Controls

– Ease Halyards

– Ease Outhauls

• Sails will be let out, air flow over sails will be

reduced, Sails will work in two modes:

– Drag Mode: Wind is pushing sails and boat down wind

– Lift Mode: Air flowing over sails produce lift when

– sailing a broad reach

–